INSTALLATION INSTRUCTIONS KK-K9-F12-K
2000-2006 FORD EXCURSION
TOOLS REQUIRED:
Power Drill
Ratchet Wrench With 6” Extension
Torx Bit Set
4 ½” Hole Saw (Exhaust Fan Option)
Caulk Gun
Standard & Metric Socket Sets
Phillips Screw Driver
7/16” Wrench
Wire Cutters / Crimping tool
HARDWARE: Some of this hardware is already attached.
QTY: DESCRIPTION:
PART #:
28
30
64
6
14
36
24
22
6
¼-20 X ½” Stainless carriage bolts
¼-20 X ¾” Stainless carriage bolts
¼-20 Serrated nuts
GSM 32022
GSM 32024
GSM 30023
GSM33001
GSM 33062
GSM 34177
GSM 34170
GSM 34169
GSM 33195
GSM33194
PRM 97343
KNM01029-SUV
¼-20 X ¾” Hex head Cap Screw Zinc
¼” X 1 ½” Hex head lag screw
#12 X ¾” Stainless sheet metal screws
#10 X ¾” Stainless sheet metal screws
#10 X ½” Stainless sheet metal screws
#10 X ¾” Sheet metal screws
#10 X ½” Sheet metal screws
Tube Silver Caulk
20
1
1
46” X 45 1/2” Rubber Mat
11 1/2 feet Adhesive Molding
SUB ASSEMBLY:
• Dome light with wire
• Tunnel edge molding
• Install exhaust fans (Optional). If locating in custom
location drill 4 ½” hole into desired location of K-9
housing. Mark and drill 3/16” mounting holes to
attach fan using (4) 10/32” X ½” machine screws and
10/32” keps nuts. Then mark and drill 3/16” holes to
mount fan guard using 10/32” X ½” machine screws
and 10/32” keps nuts.
INSTALLATION:
1. Remove interior:
• Remove rear seats
• Remove rear seat belt assembly
• Remove top, and bottom plastic rear trim caps
7. Door panels and window guards:
• Center door panels so edges do not hang over.
• Attach to door with #10 x ½” stainless sheet metal screws.
Note: window guards have holes around perimeter for permanent mounting. These holes are not used
with hinge kit! They also come flat in shipping. The guard must be pre-bent so it fits tight against the door
window frame.
• Hold window guard with pre-assembled hinge and upper bracket onto window frame.
• Make sure guard is centered on window.
• Attach hinge to lower door panel with #10 x ½” sheet metal screws.
• Mark upper aluminum bracket location on
window frame and remove from window guard.
• Attach aluminum bracket onto window frame with
#10 x ½” sheet metal screws.
• Apply adhesive molding to inner side of window
guard.
• Hinge up window guard and reattach to bracket
Upper Window Bracket
with #10 x ½” stainless machine screws and #10
stainless flat washers.
Note: this is for easy window cleaning.
8. Final steps:
• Mount dome light (fan if necessary) switch box as
desired. A switch box is provided so switch can
be mounted to K-9 housing in various locations.
(Topside of tunnel housing works very well).
Wire to 12-volt power source.
• Sheet metal seams and gaps need to be carefully
silicone at floor area. Proper sealing of
compartment will eliminate water from getting
Adhesive Molding
under the K-9 unit.
• Allow silicone to dry overnight before placing in
rubber floor mat.
KK-K9-F12-K-INST-6-06
|
Graham Field Baby Accessories 14423 2 User Manual
Grundig CRT Television LW 60 7510 TOP User Manual
Haier Washer MCS10HXCR User Manual
Hamilton Beach Microwave Oven 87108 User Manual
Hamilton Beach Oven 31160 User Manual
Hamilton Beach Slow Cooker 840149601 User Manual
Honeywell Telephone W8735B User Manual
Honeywell Thermostat TL8100 User Manual
Humax Flat Panel Television LGB 19DZT User Manual
Ice O Matic Ice Maker ICE1606 User Manual